Wireless 10y Battery Smoke Alarm Fire Decetor for Home Safety KD-108A

KD-108ABCDE Smoke Alarm

User manual

1. Brief introduction

KD-108ABCDE Smoke Alarm is a photoelectric smoke alarm with low power consumption. Internal precise analog circuit and digital circuit make the detection work more stable and reliable. The built-in 3V lithium manganese battery can provide service life of 10 years.

2. Product characteristics

◆ Photoelectric smoke detection

◆ High sensitivity

◆ Alarm memory

◆ With normal detection mode and low sensitivity detection mode (silence mode).

◆ Built-in lithium manganese battery which can provide service life of 10 years (Note: Non- Non-replaceable battery)

◆ 10-years end-of-life warning

◆ low battery warning

◆ Low power consumption

3. Technical Parameters

Technical parameters	Smoke detection
	Implementation standard	EN 14604:2005/AC:2018
	Voltage	DC3V
	Low battery warning	2.2V
	Current	Alarm current	Quiescent current
		≤120mA	≤2uA
	Status display	Standby condition	LED (red) flashes once every 344 seconds, no alarm sound
		Alarm condition or testing	LED (red) flashes and continuous alarm is given
		Low sensitivity detection (silence mode)	LED (red) flashes every 10 seconds, no alarm sound, automatically cancel low sensitivity detection 9 minutes later
		Alarm memory	If alarm has been made before, the LED (green) will flash 3 times every 43 seconds, and stops 24 hours later. The first time you press the TEST/HUSH button after alarm is made, the detector will hint by special alarm mode. When you release the button, alarm memory will be cleared.
		End of life	After power-up and work for 10 years, end-of-life warning will be made. The buzzer beeps 3 times every 43 seconds.
		Low battery warning	The product beeps once every 43 seconds.
	Alarm loudness	≥85dB/3m
	Working temperature	-10℃~+40℃
	Ambient humidity	≤95%RH (no condensation)

4. Appearance

   

Figure 1        

5. Dimensions

  Figure 2

6. Product use

    Figure 3 Functional diagram

6.1 Take out the product. Remove the mounting plate.

6.2 Insert the two hooks of the mounting plate into the slots of the product. Then turn the alarm clockwise until it snaps into place.

6.3 Testing

Press the TEST/HUSH button. The red LED will flash quickly and continuous alarm will be made. That means the detector works properly. At the same time, the detector enters low sensitivity detection mode for about 9 minutes. 9 minutes later, it will automatically exit the silence mode and enter the normal standby condition.

6.4 Low sensitivity detection (silence mode)

6.4.1 Use a small amount of smoke to make the detector alarm. Press the TEST/HUSH button. The detector will enter the silence (low sensitivity detection) mode. The red LED will flash every 10 seconds and no audible sound will be heard, unless smoke becomes denser. That will last for about 9 minutes.

6.4.2 When the detector is in silence (low sensitivity detection) mode, press the TEST/HUSH button again and alarm sound will be made. Then the detector will exit low sensitivity detection mode, and enter normal standby condition

Note: If there is still a small amount of residual smoke in the detector after the detector enters the normal standby condition, it will still alarm.

6.5 Alarm memory

If alarm has been made, alarm memory will be stored. You can tell if alarm has been made by pressing the TEST/HUSH button or observing the LED display status. The LED (green) will flash 3 times every 43 seconds, and stops 24 hours later. The first time you press the TEST/HUSH button after alarm is made, the detector will hint by special alarm mode. When you release the button, alarm memory will be cleared.

7. Installation

7.1 Choose a suitable place to install the smoke alarm.

7.2 Hold the mounting plate against the selected installation position on the ceiling, and mark the center of the holes with a pencil. Drill a hole through the pencil marks, and slide the expansion anchors into the holes.

7.3 Secure the mounting plate by screwing the support screws into the anchors.

7.4 Insert the two hooks of the mounting plate into the slots of the product. Then turn the alarm clockwise until it snaps into place.

7.5 Test the smoke alarm by pressing the TEST/HUSH button. The red LED will flash quickly and continuous alarm will be made. That means the detector works properly. At the same time, the detector enters low sensitivity detection mode, and the red LED flashes every 10 seconds. 9 minutes later, it will automatically exit the silence mode and enter the normal standby condition. You can also end the silence mode by pressing the TEST/HUSH button again.

8. Maintenance

8.1 Test the smoke alarm every week by pressing the test button.

8.2 Clean the smoke alarm every three months.

8.3 If the product does not work properly, please check the product according to 9 Failure Analysis and Troubleshooting. If the alarm still fails to operate correctly, please do not disassemble it by yourself, but seek the advice and help of the manufacturer.

9. Failure Analysis and Troubleshooting

Failure phenomenon	Cause Analysis	Remedy
The product doesn’t react when you press the TEST button	The mounting plate	Remove the detector from the mounting plate, and install it again. Insert the two hooks of the mounting plate into the slots of the product. Then turn the alarm clockwise until it snaps into place.
The product beeps once every 43 seconds.	It’s low battery warning	Stop using the product and replace it with a new one.

10. Notice

10.1 The product is not suitable for installation in hot, humid, dusty place like kitchen or bathroom.

10.2 When installing the alarm, please note that there should be no objects blocking the flash or sound of the alarm.

11. Points for Abandoned Products

11.1 The packing material is renewable, so please do your best to recycle it.

11.2 As this product has built-in non-replaceable battery, this unit cannot be abandoned with normal household garbage.