| Quantity: | |
|---|---|
KD-125C
KINGDUN
8531100000
KD-125C Smoke Alarm User Manual
2831-CPR-F2211
EN14604
1. Brief introduction
KD-125C Smoke Alarm is a photoelectric smoke alarm with low power consumption. Internal precise analog circuit and digital circuit make the detection work more stable and reliable. The product has a small size and uses large-capacity battery which can provide service life of 5 years.
2. Installation
a. Hold the mounting plate against the selected installation position on the ceiling, and mark the center of the holes with a pencil. Drill a hole through the pencil marks and use the enclosed screws and anchors to secure the mounting plate. (See Figure 3)
b. Install the batteries according to Figure 3, making sure the polarity matches the markings. If the batteries are installed correctly, the red pin will drop automatically.
c. Insert the hook of the product into the slot of mounting plate. Then turn the alarm clockwise until it snaps into place.
Note: If you can't rotate the alarm after insert the hook into the slot, please check if the battery is installed correctly.
3. Technical parameters
Technical parameters | Smoke detection | ||
Voltage | DC3V（AAA*2） | ||
Low battery warning | 2.2V | ||
Current | Alarm current | Quiescent current | |
≤120mA | ≤2uA | ||
Status display | Standby condition | LED (red) flashes once about every 344 seconds, no alarm sound | |
Alarm condition or test | LED (red) flashes and continuous alarm is given | ||
Low sensitivity detection (silence mode) | LED (red) flashes every 10 seconds, no alarm sound, automatically cancel low sensitivity detection about 9 minutes later | ||
Alarm memory | LED (green) flashes 3 times about every 43 seconds, and that stops 24 hours later. The first time you press test/hush button after alarm is made, the detector will hint by special alarm mode. | ||
Low battery warning | The product beeps about every 43 seconds | ||
Alarm loudness | ≥85dB/3m | ||
Working temperature | -10℃~+40℃ | ||
Ambient humidity | ≤95%RH (no condensation) | ||
KD-125C Smoke Alarm User Manual
2831-CPR-F2211
EN14604
1. Brief introduction
KD-125C Smoke Alarm is a photoelectric smoke alarm with low power consumption. Internal precise analog circuit and digital circuit make the detection work more stable and reliable. The product has a small size and uses large-capacity battery which can provide service life of 5 years.
2. Installation
a. Hold the mounting plate against the selected installation position on the ceiling, and mark the center of the holes with a pencil. Drill a hole through the pencil marks and use the enclosed screws and anchors to secure the mounting plate. (See Figure 3)
b. Install the batteries according to Figure 3, making sure the polarity matches the markings. If the batteries are installed correctly, the red pin will drop automatically.
c. Insert the hook of the product into the slot of mounting plate. Then turn the alarm clockwise until it snaps into place.
Note: If you can't rotate the alarm after insert the hook into the slot, please check if the battery is installed correctly.
3. Technical parameters
Technical parameters | Smoke detection | ||
Voltage | DC3V（AAA*2） | ||
Low battery warning | 2.2V | ||
Current | Alarm current | Quiescent current | |
≤120mA | ≤2uA | ||
Status display | Standby condition | LED (red) flashes once about every 344 seconds, no alarm sound | |
Alarm condition or test | LED (red) flashes and continuous alarm is given | ||
Low sensitivity detection (silence mode) | LED (red) flashes every 10 seconds, no alarm sound, automatically cancel low sensitivity detection about 9 minutes later | ||
Alarm memory | LED (green) flashes 3 times about every 43 seconds, and that stops 24 hours later. The first time you press test/hush button after alarm is made, the detector will hint by special alarm mode. | ||
Low battery warning | The product beeps about every 43 seconds | ||
Alarm loudness | ≥85dB/3m | ||
Working temperature | -10℃~+40℃ | ||
Ambient humidity | ≤95%RH (no condensation) | ||
