| Quantity: | |
|---|---|
KD-127B
8531100000
Smoke alarm devices KD-127A
1134-CPR-124
EN14604
The instruction of smoke alarm devices
1. Shape and size
2. Technical parameter
Working Voltage：9V DC(re-commanded battery:6F22,GP 1604S,GP 1604A,
PAIRDEER 6F22,OSEL 6LR61,PAIRDEER 6LR61,FORTE ER9V,
EVE CR-9V,ULTRALIFE ULVL-J,FANSO ER9V)
Current： Quiescent Current：≤12uA
Alarming Current: ≤ 20mA
Alarming Decibel：≥85dB/3m
HUSH Status：LED flashes every 10S
Standby status：LED flashes every 43S
Low battery status: special low battery beep around every 43S
LED Indicator：LED（Red）
Low voltage Alarming：≤7.35V
Working Temperature：-10℃~+40℃
Working Humidity：≤95%RH(no water gel)
3. Test and before installation:
Note：If the battery is not installed correctly, the detector will not work and maybe destroyed.
If the detector operates smoothly, the Red LED will flash once in about 43S.
Take the product out of the packaging,take off the installation base from the product via rotating the product on the anti-clockwise direction.
Take out the 9V battery from battery compartment, remove the insulation film from the battery, connect the battery to battery buckle and put it back to battery compartment.
Depress(keep depressing and release till finish the testing) the test/hush button，the RED LED flashes quickly and in the meanwhile the detector sounds, which means the the detector works well. At the same time the product goes into low sensitivity detection mode, round 10 minutes later the product goes into standard sensitivity detection mode again.
4. Installation
(1) Choose a right place to install the smoke alarm.
The alarm may not be mounted In:
A) a room in which the temperature can reach below -10°C and above 40°C.
B) in damp spaces
C) just in front of doors or windows and not near a ventilator or radiator
D) Maintain a distance of at least 50 cm from fluorescent lights or low-energy bulb.
(2) Fix two plastic screw base into ceiling according to installation hole position of smoke alarm base
(3) Fix the installation base on ceiling via screws at pre-installed screw base.
(4) Make sure the battery is installed and well connected to the smoke alarm (you may use the test button function to check) and fasten the smoke alarm to pre-installed base via clockwise rotation.
(5) Use the test button again to make a final check.
5. Maintain and use
Test the smoke alarm weekly and after battery replacement.Test the alarm for normal operation using the test facility when the battery is replaced.
If the product does not work properly, please check the product according to Failure Analysis and Troubleshooting part as below.If the product still can not work please contact your local dealer and do not open the product by yourself.
6. Failure Analysis and Troubleshooting
Failure phenomenon | Cause Analysis | Remedy |
No reaction from product when depress test button | 9V battery may not installed properly | Installed the 9V battery with right Battery polarity |
Low battery beep around every 43 S | Low voltage of 9V battery | Replace the battery |
7. Notice
(1) This product is not re-commanded to be installed in humidity,dusty, high temperature place like Kitchen or bathroom
(2) During the installation please make sure that there will be no other obstacle which may cover the flash light or alarm sound from the smoke alarm.
(3) Smoke alarm can not work if the battery is not connected to the right battery polarity, and the product may also be destroyed because of this.
Smoke alarm devices KD-127A
1134-CPR-124
EN14604
The instruction of smoke alarm devices
1. Shape and size
2. Technical parameter
Working Voltage：9V DC(re-commanded battery:6F22,GP 1604S,GP 1604A,
PAIRDEER 6F22,OSEL 6LR61,PAIRDEER 6LR61,FORTE ER9V,
EVE CR-9V,ULTRALIFE ULVL-J,FANSO ER9V)
Current： Quiescent Current：≤12uA
Alarming Current: ≤ 20mA
Alarming Decibel：≥85dB/3m
HUSH Status：LED flashes every 10S
Standby status：LED flashes every 43S
Low battery status: special low battery beep around every 43S
LED Indicator：LED（Red）
Low voltage Alarming：≤7.35V
Working Temperature：-10℃~+40℃
Working Humidity：≤95%RH(no water gel)
3. Test and before installation:
Note：If the battery is not installed correctly, the detector will not work and maybe destroyed.
If the detector operates smoothly, the Red LED will flash once in about 43S.
Take the product out of the packaging,take off the installation base from the product via rotating the product on the anti-clockwise direction.
Take out the 9V battery from battery compartment, remove the insulation film from the battery, connect the battery to battery buckle and put it back to battery compartment.
Depress(keep depressing and release till finish the testing) the test/hush button，the RED LED flashes quickly and in the meanwhile the detector sounds, which means the the detector works well. At the same time the product goes into low sensitivity detection mode, round 10 minutes later the product goes into standard sensitivity detection mode again.
4. Installation
(1) Choose a right place to install the smoke alarm.
The alarm may not be mounted In:
A) a room in which the temperature can reach below -10°C and above 40°C.
B) in damp spaces
C) just in front of doors or windows and not near a ventilator or radiator
D) Maintain a distance of at least 50 cm from fluorescent lights or low-energy bulb.
(2) Fix two plastic screw base into ceiling according to installation hole position of smoke alarm base
(3) Fix the installation base on ceiling via screws at pre-installed screw base.
(4) Make sure the battery is installed and well connected to the smoke alarm (you may use the test button function to check) and fasten the smoke alarm to pre-installed base via clockwise rotation.
(5) Use the test button again to make a final check.
5. Maintain and use
Test the smoke alarm weekly and after battery replacement.Test the alarm for normal operation using the test facility when the battery is replaced.
If the product does not work properly, please check the product according to Failure Analysis and Troubleshooting part as below.If the product still can not work please contact your local dealer and do not open the product by yourself.
6. Failure Analysis and Troubleshooting
Failure phenomenon | Cause Analysis | Remedy |
No reaction from product when depress test button | 9V battery may not installed properly | Installed the 9V battery with right Battery polarity |
Low battery beep around every 43 S | Low voltage of 9V battery | Replace the battery |
7. Notice
(1) This product is not re-commanded to be installed in humidity,dusty, high temperature place like Kitchen or bathroom
(2) During the installation please make sure that there will be no other obstacle which may cover the flash light or alarm sound from the smoke alarm.
(3) Smoke alarm can not work if the battery is not connected to the right battery polarity, and the product may also be destroyed because of this.
